DSM-26MKII ORDERCODE D2072 Highlite International B.V. Vestastraat 2 6468 EX Kerkrade The Netherlands
9 Menu Overview
11 Input setup 1. Push and hold the Ch A input mute/edit button(1) for 3 seconds to enter edit mode for input channel A. While in edit mode, the e
12 3. Push the X-OVER(4) button to enter the X-over menu. Tap the X-OVER(4) button to select either a Low Pass Filter (LPF) or a High Pass Filter (HP
13 8. Use the jogwheel(9) to enter a name for your new preset. Dial to edit a character and click to select the next character. Push and hold the jog
14 Lock Menu Setup The lock menu allows you to block parameters for accidental changes. You are able to block each parameter for each input and outpu
15 Dial and click the jogwheel(9) to select “change password” if you want to change the password you previously set up and continue with step 11. S
16 Backlight Setup Dialing the jogwheel(9) allows you to select: 1. Open Select “Open” if want to keep the backlight always on. Confirm by clickin
17 Installing the CP2103 USB driver Make sure the DSM-26MKII is not connected to your computer while installing the USB driver. Click “USB Driver I
18 Click the back button to return to the setup window. Installing the Digital Speaker Manager software Click “Application Installation” The D
1 Congratulations! You have bought a great, innovative product from DAP Audio. The DAP Audio DSM-26MKII brings excitement to any venue. Whether you w
19 Click next to proceed Click the Finish button. Now you’re ready with the installation of the Digital Speaker Management software. Exit the
20 Connecting a single DSM-26MKII using the USB port Use the supplied USB cable to connect your DSM-26MKII with your PC. The drawback of this connect
21 Making a connection between your PC and DSM-26MKII Connect your DSM-26MKII to your PC using the included USB cable or via the optional USB/RS485 c
22 Software operation The Digital Speaker Management window can be divided into 3 zones: A. The information zone B. The display and connections z
23 After storing and naming a program, the name of the program will be shown in the upper row and the number of the program will be shown in the bo
24 PC program Is for exchanging programs between Digital Speaker Management and your hard disk or other storage media. Recall program from PC Allows
25 C. the parameter adjustment zone Channel selection Click the channel button (INA, INB, INC, IND, OUT1, OUT2, OUT3, OUT4, OUT5, OUT6, OUT7 or
26 Curve button Clicking the curve button allows you to display the corresponding EQ curve in the display(3). The link function The Digital Spea
27 Clicking the EQ/Bypass button allows you to bypass the complete EQ section. Delay The parameters can be adjusted by clicking the increase/decr
28 Source The source window indicates which source(s) is(are) connected to the selected output channel. Clicking the checkbox allows you to change
2 DAP Audio DAP Audio DSM-26MKII™ Product Guide Warning ...
29 Compensation of interference with balanced connections Maintenance The DSM-26MKII crossover requires almost no maintenance. However, you shoul
30 Product Specifications Model: DAP Audio DSM-26MKII Input gain: -80dB - +12dB, step @ 0,1 dB Input selection: Each input channel can be con
2013 Dap Audio.
3 Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all
4 Do not switch the system on and off in short intervals, as this would reduce the system’s life. Only use system indoor, avoid contact with wa
5 Operating Determinations This system is not designed for permanent operation. Consistent operation breaks will ensure that the system will serve yo
6 Description of the device Features The DAP DSM-26MKII is professional 2 in- and 6 output speaker manager that can be used for a wide range of appl
7 9) Jogwheel Dialing the jogwheel allows you to change parameters. Clicking the jogwheel allows you to enter, select or confirm. 10) EXIT button
8 Installation Remove all packing materials from the DSM-26MKII. Check that all foam and plastic padding is removed. Screw the equipment into a 19&qu
Comments to this Manuals